top of page
Chindelas Final Photos Driveway Polyaspartic Floor Concrete Coatings in Tidalwave

Chindelas Project

Tidal Wave Polyaspartic Driveway Coating

PROJECT DETAILS

Case Study: Transforming a 581 SQFT Driveway and Walkway in Ocala, Florida


Mr. Chindelas had seen decorative coatings around his community and wanted to bring that finished appearance to his own driveway and walkway. His concrete was approximately three years old and was described as being in good condition. His interest centered on improving the appearance of the entrance while selecting a coating suitable for vehicle traffic.


The border was an important part of the design. Mr. Chindelas and his wife liked the framed appearance of a neighboring driveway and shared a reference for the look they wanted. The project brought together a decorative flake surface and a separate solid color border, with the treatment continuing along the walkway toward the front entrance.


The Challenge:


Preparing Existing Concrete and Defining the Design

The driveway had an uneven, discolored appearance, with existing joints dividing the slab. Although the project did not begin with a failing coating, the bare concrete still required mechanical surface preparation before the new system could be applied. A sound looking slab must be assessed and prepared for coating adhesion.



The design also required attention to scale. The installation plan called for a 4 inch border around the driveway and a 2 inch border around the sidewalk, with the dimensions to be verified with the customer before coating. Carrying the border around the turns of the walkway required a controlled layout and clearly defined edges.


The Solution:


Full Flake Coverage with a Separate Border Application

Tru-Grit selected a polyaspartic coating approach for the measured 581 sq ft area. The substrate assessment included moisture and hardness readings. Based on that assessment, the installation plan did not call for a Moisture Vapor Barrier primer.


The coating sequence established the full flake system across the included surfaces before adding the decorative border over the flake finish. Solid pigmented Poly 85 Regular Cure was specified for the border. This allowed the main decorative surface to continue through the driveway and walkway while the solid coating defined their perimeter.


The Process:


Surface Preparation, Flake Broadcast and Finish Coating

Mechanical surface preparation. The crew mechanically prepared the existing concrete across the driveway and adjoining walkway. This stage addressed the surface receiving the coating and established the foundation for the base coat. The existing joint layout remained defined within the finished design.


Base coat and full flake broadcast. Following preparation, the crew applied the base coat and broadcast decorative flakes across the surface. Full flake coverage created the continuous patterned field through the open driveway and the narrower approach to the entrance.


Protective finish coat. The installation sequence included a topcoat over the decorative flake system. The project specification also included ALUMX high wear additive and a slip resistance additive, addressing wear and traction as part of the coating selection.


Custom solid border. The border was a separate application after the main flake system. The installation instructions specified fiber tape to control the edges and limit coating bleed beneath the tape. Pigmented Poly 85 was then used over the flake surface to create the solid perimeter detail.


The Outcome:


A Coordinated Driveway and Walkway

The original installation changed the Chindelas entrance from exposed, discolored concrete to a continuous decorative finish. The coated surface extends from the driveway into the walkway, bringing the approach to the front door into the same design. Existing slab divisions remain visible, and the solid border adds a distinct perimeter treatment.


For homeowners considering a similar improvement, this project shows how preparation and layout contribute to the finished appearance. The coating system addresses the concrete surface, while the border width and placement shape how the driveway connects visually with the home.


Considering a Decorative Driveway Coating?

Talk with Tru-Grit about your existing concrete, the areas you want to include and the appearance you want to achieve. We can review the preparation requirements and help you compare a full flake finish with custom border options for your property.

Final Project Photos

Chindelas Final Photos Driveway Polyaspartic Floor Concrete Coatings in Tidalwave
Ready to Finally Get the Space You’ve Been Wanting?

Tell us what you want to change and how you want to enjoy the space. We’ll help you create a finished floor that looks great, fits your life, and gives you something to be proud of for years to come.

Opening Hours:

Tru-Grit Garage Flooring LLC

Central Florida Luxury Polyaspartic Epoxy

Flooring For Residential and Business Solutions

Mon - Fri: 7AM - 4:30PM Eastern

  • Facebook Tru Grit Epoxy Flooring Central Florida
  • Instagram
  • Youtube
  • Pinterest
  • LinkedIn
  • Quora

Sat - Sun: Closed

White phone icon in a red circle
White location pin icon on a red circle background
White envelope icon in a red circle for email contact
Red and white clock icon representing time management.

By appointment only*

@2026 Tru Grit Garage Flooring. All Rights Reserved.

Home  |  Services  |  Gallery  |  Case Studies  |  Blog  |  Contact Us

bottom of page